Updated cookies policy - you'll see this message only once.

Pabrec.com uses cookies on this website. They help us to know a little bit about you and how you use our website, which improves the browsing experience and marketing - both for you and for others. They are stored locally on your computer or mobile device. To accept cookies continue browsing as normal. Or go to the cookies policy for more information and preferences.
 
We will be glad to make special offer for wholesaler a special offer special offer for wholesale for wholesale customers.
Please don't hesitate to contact us

Dekotla E-2000 Epoxy Coating

A thick self levelling epoxy coating with UV resistance.

exc.VAT 22%

This product is not available. Please select other variation.

Product details of Epoxy coating

Dekotla E-2000 is an excellent choice for heavy wear areas. Simply mix and pour, then spread with Applicator and the product "self levels" to a hard wearing surface. Running a spiked roller over the surface prevents air bubbles.

- Seamless, smooth satin finish
- UV resistance
- Excellent mechanical and chemical resistance
- New, easy to use formula
- Exceptional wear resistance

The thick, satin coating helps fill and disguise imperfections in the floor.

Resistant to: detergents, petrol, diesel fuel, xylene, methylated spirits, white spirit, bleach, anti freeze, mineral oil, sugar solutions and salt

Discolouration of some shades may occur with strong or hot chemicals. please consult our technical department for advice on chemicals not listed.

Coverage: approx. 13m² per 25kg

Specification of Epoxy Coating Dekotla E-2000

Appearance gloss
Primer Required yes
Usage - Interior / Exterior interior 
Usage - Properties extremely tough, easy to apply, can be used over existing coatings, virtually odourless - can be applied in confined areas, easy to mix, mid-gloss finish, excellent resistance to oils and solvents, independently tested to BS476 for Class 1 Fire Resistance
Usage - Surfaces floor
Max Operational Temp (deg C) 25
Coverage (m² per kg) 6-7
Operational Temp (deg C) 16-25
Application - Pot Time (hours) 0.5 at 23 degrees
Dust dry (at +23°C, 50% R.H.) 2-4 hours
Light pedestrian traffic (at +23°C and 50% R.H.): 24 hours
Final hardening time (at +23°C): 6 days
Application - Recommended Coats 2

Preparation and Application

Surface Preparation

Dekotla E-2000 can be used on previously coated surfaces, which must be abraded to provide a key and all poorly bonded coatings must be removed. A trial area is recommended to test the effect on previous coatings.
Bare concrete substrates should be at least 4 weeks old, clean and reasonably dry. Concrete with laitance (a weak dusty layer on the surface) should be prepared by mechanical abrasion or an acid based preparatory agent which helps to remove loose cement deposits and provide a key. Very smooth, non porous or power floated surfaces should be mechanically abraded.
Dekotla E-2000 should only be laid at floor surface temperatures between 15°C and 35°C.

Mixing

Stir the contents of each tin thoroughly. Using a mixing blade fitted to a slow speed electric drill, start to mix while slowly adding the curing agent. Scrape around the inside of both tins to ensure all the material has been removed. When thoroughly mixed add the fine aggregate component steadily until uniform in colour and consistency and continue blending for a further 5 minutes, ensuring that all material at the sides and base are thoroughly mixed. It is possible to hand mix small quantities but great care must be taken.

Application

Working in sections of approximately 5m², pour the mixed Dekotla E-2000 on to the prepared surface and spread evenly to the desired depth of 1-2mm using a notched squeegee. Within approximately 5-10 minutes, apply a spiked roller to remove air bubbles. Repeat a few minutes later and thereafter until air bubbles cease. Spike rollering can extend into the previously applied section, but ensure that this has not hardened to such a degree that spiked rollering will damage it. If a knife cut in the wet surface heals quickly, the surface is still safe to roller. Spiked shoes will help operators to reach all areas of the uncured floor.